Rane MM 12 Manuel d'utilisateur télécharger pdf (Page 13)

V. SPECIFICATIONS

12 INPUTS with the following:

-Transformerless electronically balanced/unbalanced female three-pin connector input.

-Passive MIC splitter with male three-pin connector output.

-Built-in RFI filters.

-Input impedance: 8k ohms in MIC or LINE.

-Active gain control: 20 dB to 70 dB in MIC. 10 dB to 30 dB in LINE.

-Maximum input leve!s: +2 dBm (1V) in MIC. +12 dBm (3V) in LINE.

-Overload LED indicator: lights at 4 dB below clipping (+16 dBm).

-Three-way input equalizer:

Bass: ±14 dB @ 20 Hz. shelving type

Midrange: ±10 dB @ 1k Hz, bandpass type

Treble: ±12 dB @ 20k Hz, shelving type

-Equivalent input noise: -120 dBm unweighted, with source impedance of 200 ohms,

20k Hz bandwidth.

-Effects loop: TRS (Tip/ring/sleeve) 1/4” jack tip=send, ring=return, sleeve=ground,

located POST EQ.

-AUX input: 1/4” jack, summing input located POST EQ.

6 OUTPUTS with the following:

-Transformerless, high-current floating stereo 1/4” output jack, compatible with bal-

anced or unbalanced inputs.

-Maximum output level:

+19 dBm (7.0 V into 600 ohms, 20-20k Hz).

-Minimum output load impedance: 600 ohms.

-Output impedance: 50 ohms.

-Two-band parametric equalizer

Amplitude: 12 dB boost 15 dB cut

Frequency: 40 - 1k Hz in Bass, 1k - 10k Hz in Treble.

Bandwidth: 1 octave in WIDE, 1/3 octave in NARrow.

-Overload LED indicator:

lights at 4 dB below clipping (+16 dBm).

-Expand input 1/4” summing input pre-fader and preEQ, unbalanced.

HEADPHONE CUE AMPLIFIER:

-700 mW maximum average (RMS) power output per 8 ohm headset 350 mW per chan-

nel, 20 - 20k Hz

-Maximum Gain: 28 dB.

-THD + Noise: less than 0.1% typical; less than 0.4% 20 - 20k Hz

-Signal/Noise Ratio: 98 dB below rated 350 mW into 8 ohms, A-weighted.

-Frequency response: 20 - 20k Hz, +0/-3 dB.

-Mains Input: auxiliary input to cue system, patched to headphone output when all

CUE buttons are disengaged; input impedance of 2.2 k ohms.

OVERALL PERFORMANCE: Any MIC input to any output with EQ flat

THD + Noise: less than .03% @ +4 dBm.

IM Distortion (SMPTE) @ +4 dBm:

less than .03%

Frequency Response:

20 - 20k Hz, +0/-3 dB.

Slew Rate: 10 V/µS.

GENERAL SPECIFICATIONS:

Dimensions: 21” H X 19” W X 2½” Rack depth, EIA Rack mountable.

Construction: All steel chassis.

Weight: 24 Ib net

1 2 ... 8 9 10 11 12 13

Commentaires sur ces manuels

Pas de commentaire

Rane MM 12 Manuel d'utilisateur Page 13

Commentaires sur ces manuels

Produits connexes et manuels pour Audio Rane MM 12