Rane SRM 66 Manuel d'utilisateur Page 1

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Audio Rane SRM 66. Rane SRM 66 User Manual Manuel d'utilisatio

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 10
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 0
Manual-1
SRM 66
SPLITTER ROUTER MIXER
OPERATORS MANUAL
Quick Start
Before complaining about having to install the SRM 66 in
the rack twice (because you forgot to set the internal highpass
lters ahead of time), take note that the very first (non-joke)
line in this manual is: Before installing the SRM 66 in a rack,
be sure the internally switchable 80 Hertz highpass filters are set
as desired. ey are shipped with the filters in the OUT (disabled)
position. (See the bottom of page Manual-2 to enable these filters.)
If you were smart enough to read this much of the manual, this
paragraph may already have saved you a few minutes of your
life – youre welcome. If you’ve learned the hard way, hopefully
youve learned an important lesson – read at least the first line in
the manual first.
Make all connections with the power and amplifiers off. e
SRM 66 is fully balanced and equipped with removable 5-posi-
tion Euroblock connectors. Inputs and Outputs are arranged on
Euroblocks in pairs, i.e., 1&2, 3&4, 5&6.
Be sure the FP LOCK switch (on rear) is in the out position
to enable programming from the front panel.
Apply power so the PWR LED lights and LCD screen glows
with the SRM 66 welcome marquee. During initialization, the
startup muting circuit immediately starts counting down from
40 in the Limiter Gain Reduction area of the display. Adjust the
VIEWING ANGLE with a miniature screwdriver if necessary.
With signal applied to the Inputs, watch the MIX INPUT
HEADROOM indicators. ese verify correct setting of the
Output of the previous device and the rear panel Input GAIN
switches. Adjust so that 4 dB lights during peaks.
Navigating the LCD Edit pages is simple. e top buttons
marked << and >> are the left/right Page scroll buttons. ese
navigate to Output pages 1 through 6, the assign Outputs to
Output Group page, the assign Remote to Group page, the assign
Group to Master Remote page, the Group Levels page, and the
Memory page.
WEAR PARTS:is product contains no wear parts.
e bottom buttons marked
< and > are the left/right cursor
buttons. ese select the (underlined) parameter to edit.
Rotating the DATA knob changes the parameter setting.
Let’s start by navigating to Output 1s page. Move the cursor
under IN1. With a signal driving Input 1 and a working ampli-
fier connected to Output 1, adjust the DATA knob to the desired
level. Adjust any other Input going to Output 1. MST controls
the Master level of Output 1. LIM sets the Limit reshold of
the Limiter circuit for Output 1.
To Copy settings from Output 1 to any other Output, move
the cursor to Copy. Press the EXE button. e display now
reads Paste. Change the page to the one you want these same
settings in, and press EXE again. e settings have now been
pasted into the new Output.
Settings may be Stored and Recalled in the Memory Page. To
Store, select the Store field, select a Memory number with the
DATA wheel and press EXE. To Recall, select the Recall field,
select a Memory number with the DATA wheel and press EXE.
Look deeper into this manual for information on remote control
of Memories, level adjustments and, the most powerful feature
of the SRM 66, Output Groups which “link” Output levels. A
Master Remote feature allows controlling the level of any Output
Groups assigned to it.
For best signal control and dynamic range, turn the Master
Output off when no Inputs are routed to a given output.
CAUTION: Never connect anything except an approved
Rane power supply to the thing that looks like a red telephone
jack on the rear of the SRM 66. is is an 18 VAC center
tapped power input. Consult the Rane factory for a replacement
or substitute.
16dB
4dB
SPLITTER
MIXE
R
ROUTER
SRM 66
1 432
MIX INPUT HEADROOM
65
EXE
DATA
PWR
SHIFT
VIEWING
N
ANGL
E
X
M
I
A
M
Vue de la page 0
1 2 3 4 5 6 7 8 9 10

Résumé du contenu

Page 1 - OPERATORS MANUAL

Manual-1SRM 66SPLITTER ROUTER MIXEROPERATORS MANUALQuick StartBefore complaining about having to install the SRM 66 in the rack twice (because you for

Page 2 - Front Panel Description

Manual-10©Rane Corporation 10802 47th Ave. W., Mukilteo WA 98275-5098 TEL 425-355-6000 FAX 425-347-7757 WEB www.rane.com105147AMX &

Page 3 - 4 352 1 6

Manual-2Front Panel Description MIX INPUT HEADROOM meters. ese assist setting of the rear panel GAIN switches as well as the output level of the pre

Page 4 - SRM 66 Connection

Manual-3Rear Panel Description POWER input connector. Use only an RS 1, or other Remote AC power supply approved by Rane. is unit is supplied with a

Page 5 - Operation

Manual-4SRM 66 ConnectionBalanced OperationConnect the ‘+’ to ‘+’, ‘–’ to ‘–’, and shield to shield. Use only when driving from a true balanced source

Page 6 - Copy G1 Off G6 G4 G3 G2

Manual-5Output Page, where [x] indicates the Output currently being edited.Limiter gain reduction is indicated in [y]dB when the Limiter is active.Out

Page 7 - Figure 7. Memory Page

Manual-6Group attenuation levels page. This has the same action as controlling from optional SR 1 Remote(s).Group Lvls G1 G2 G3 G4 G5 G6Zero All -20 -

Page 8 - PagingBinary

Manual-7Mem[n]* Store RecallMemory [n] Stored! [ n] [ n]*RIP[SR1]InitFactMemory location to Recall. Select Memory with DATA wheel and press EXE to Rec

Page 9 - Applications

Manual-8MRP and RIP ConnectionsWhen wiring to Euroblocks, a minimum wire gauge of 22 is preferred for reliability. If the ground or shield wire is lef

Page 10 - AMX & Crestron

Manual-9Figure 9. Manufacturing Facility SystemApplicationsOne of the best ways to grasp the true versatility of the SRM 66 is to observe one in actio

Commentaires sur ces manuels

Pas de commentaire