Rane SRM 66 Manuel d'utilisateur télécharger pdf (Page 7)

Manual-7

Mem[n]* Store Recall

Memory [n] Stored! [ n] [ n]

RIP

[SR1]

Init

Fact

Memory location

to Recall. Select

Memory

with

DATA wheel and

press EXE to

Recall

Selects mode for the

Remote Interface Port.

Select SR1 when used

with SR 1 Remote

devices. DSC mode

allows future

communication options.

Memory location to

Store. Select Memory

with DATA wheel and

press EXE to Store.

After Execution, this

conﬁrms that Memory

[n] has been Stored

or Recalled.

Selects mode for

standard Factory or

preset Room Combine

Programs

Memory page. The

indicates current

parameter settings do not

match the recalled

Memory; [n] indicates the

last recalled Memory.

Figure 7. Memory Page

Memories

24 non-volatile Memories can save up to 24 system conﬁgu-

rations. Each Memory contains these parameters:

Mix Source Routing Input 1-2-3-4-5-6 to each Output

Mix Source Levels +6 dB to -25 dB for each Output

Master Level Reduction +0 dB to -59 dB for each Output

Limit reshold Max (0 dBr) to -28 dBr, each Output

Output to Group Assignments

Remote to Group Assignments

Memories are stored and recalled using the Memory page

shown in Figure 7.

Memory Recall Port

In addition to the Memory page, the SRM 66 provides a

Memory Recall Port (MRP). is port allows remote switch clo-

sures to recall any of the twenty-four system Memories. e ﬁrst

eight Memories recall with simple switch closures on the eight

MRP pins (see the Normal section of Table 1).

A binary wiring mode allows accessing all 24 Memories (see

the Binary section of Table 1). Simply hardwire connect the

Memory Recall Port (MRP) terminals numbered 5, 6 and 8 to

the COM terminal. is will enable the unit to accept binary

memory recall input and yield 24 memories.

“Paging” mode provides installers an easy way to conﬁgure

a system which uses a single switch (such as a push-to-talk mic

switch) to toggle between two sequential Memories to change

source levels. See Figure 8 and Table 1.

MRS 4 Memory Recall Switch

e optional MRS 4 accessory provides a simple solution

to recalling four Memories from a remote location. e MRS 4

mounts in a standard U.S. electrical box with a minimum depth

of 2.25" (5.5 cm). If connected to the MRP in Normal mode,

this remote allows up to 4 Memories to be recalled. See the Nor

mal section of Table 1 on the following page. See the

MRS 4 Data Sheet for hookup and operating instructions.

RCP 3 and RCP 4 Room Combining Panels

e optional RCP 3 (three-room combining panel) and RCP

4 (four-room combining panel) accessories show a graphical

representation of the rooms to be combined. Operation is very

intuitive. To combine adjacent rooms, the end user simply pushes

the button that straddles the desired rooms. Once the button’s

color becomes green, the rooms are “combined”. To uncombine

the adjacent rooms, the end user simply re-pushes the button.

e button’s color now becomes black, identifying the room’s

status as “uncombined.”

e RCP 3 and RCP 4 panels mount in a standard 19” rack

and utilize a single rack space. To create a “room combining

system”, the installer only has to connect the RCP 3 (or RCP 4)

to the MRP, and 3 (or 4) SR 1L’s to the RIP of an SRM 66. See

the RCP Data Sheet for hookup and operating instructions.

Figure 8. MRP Wiring

87654321C

Mic

Switch

Memory

Switch

Paging

Mode

DSC 1

DIGITAL

SERIAL

CONVERTE

INPUT

RS 232 DATA

INTERFACE

REMOT

PORT (RIP)

RANE CORP.

MADE IN U.S.A.

DSC 1 & SRM Exchange

e optional Rane DSC 1 accessory provides a bridge to

connect a PC’s RS-232 port and the SRM 66’s Remote Interface

Port. Coupled with the included SRM Exchange Software, the

DSC 1 allows the exchange of settings between an SRM 66 and

SRM Exchange. Once the settings are obtained by the PC, they

can be manipulated, stored in a ﬁle, printed for future reference

or sent to subsequent SRM 66s. SRM Exchange software can be

downloaded from www.rane.com. e software allows SRM 66

programming “oﬄine” without an SRM 66 present; however,

the DSC 1 is required to download these settings to the SRM

66. See the DSC 1 Data Sheet for hookup and operation.

For programming the Memory Recall Port using the Edit

MRP button, see the RaneNote “Advanced Applications for the

Ingenious SRM 66 and SR 1L.”

1 2 3 4 5 6 7 8 9 10

Commentaires sur ces manuels

Pas de commentaire

Rane SRM 66 Manuel d'utilisateur Page 7

Commentaires sur ces manuels

Produits connexes et manuels pour Audio Rane SRM 66