Rane MP 4 Manuel de l'opérateur Page 4

  • Télécharger
  • Ajouter à mon manuel
  • Imprimer
  • Page
    / 19
  • Table des matières
  • MARQUE LIVRES
  • Noté. / 5. Basé sur avis des utilisateurs
Vue de la page 3
Manual-4
Rear Panel Description
1 Universal Voltage Input: via a miniature IEC 60320 C6 appliance inlet. is mates with an IEC 60320 C5 line cord (USA
domestic). Do not lift the ground connection!
2
USB
connection: Attach the included USB cable from here to the computer. e blue LED illuminates when the cable is con-
nected and receiving power. USB delivers two stereo inputs from the computer to the mixer (
USB 1
and
USB 2
), and one stereo
record signal from the mixer to the computer.
3
HOUSE
Output: e front panel
HOUSE LEVEL
control affects the volume at this Output. Connect either the XLR or ¼" TRS
(tip-ring-sleeve) jacks to a balanced equalizer or amplifier. Both Output types may be used simultaneously if needed. ough not
recommended, unbalanced ¼" TS (tip-sleeve) cables may be used for short runs (under 3 meters [10 feet]) to an amplifier with
unbalanced inputs. See the RaneNoteSound System Interconnection for wiring recommendations.
4
AUX
Output:is delivers the same signal as the
HOUSE
Output, but has its own rear panel LEVEL control. is Output is not af-
fected by the front panel
HOUSE LEVEL
control. ese balanced ¼" TRS (tip-ring-sleeve) Outputs connect to a balanced equalizer
or amplifier (for a possible second listening zone) and follow the same interconnection rules as above.
5 MIC TO USB RECORD switch: In the YES position the Mic signal along with the Program mix is routed to the USB record output.
In the NO position only the Program mix is sent to the USB record output.
6
INPUTS 1 & 2
: ese stereo Inputs are each switchable from a PHONO (RIAA) stage for magnetic cartridges (switch in) to a LINE
level Input suitable for any line level device such as a CD player (switch out). Each of these may be assigned to
PROGRAM A
or
B
using the front panel
INPUT
selectors. e PHONO GROUND screw connects those extra wires coming out of the turntables.
7
MIC
Input jack: Accepts either a ¼" balanced (TRS) or unbalanced (TS) microphone plug, controlled by the front panel
MIC
LEVEL
control.
MADE IN U.S.A.
RANE CORP.
RIGHT LEFT RIGHT RIGHTLEFT LEFT
LEVEL
R
L
PHONO
LINE
PHONO
GROUND
MIC TO
USB RECORD
MP 4
HOUSE AUX
IN 2 IN 1
MIC
ACN 001 345 482
BALANCED OUTPUTS: TIP = (+), RING = (–), SLEEVE = SIGNAL GROUND
BALANCED INPUT
PHONO
LINE
YES
NO
USB
100-240V
7 WATTS50/60 Hz
FOR CONTINUED
GROUNDING PROTECTION
DO NOT REMOVE SCREW
1 2 75 6
3 4
Fader Cleaning
With heavy use in harsh environments, the fader may need
lubrication. is treatment extends longevity and can make a
used fader as good as new. e fader assembly must be removed
from the MP 4 for proper cleaning. We recommend any of the
following cleaning solutions:
Caig Cailube MCL 100% spray lubricant
Caig Cailube MCL 5% spray cleaner
CRC 2-26 (www.crcindustries.com)
Order CaiLube MCL
®
from:
CAIG Laboratories, Inc.
12200 atcher Ct.
Poway, CA 92064
Phone 858-486-8388
Fax 858-486-8398
Web www.caig.com
CLEANING INSTRUCTIONS
A. Fader assembly replacement (part #11646)
1. Unplug the MP 4.
2. Remove the bottom cover.
3. Remove the fader screws from the front panel.
4. Draw fader assembly out through the bottom.
5. Remove ribbon cable from old fader.
6. Attach ribbon cable to new fader, screw onto front panel and
replace bottom cover.
B. Fader cleaning
1. Hold the fader assembly away from the mixer.
2. Position the fader at mid-travel.
3. Spray cleaner/lubricant into both ends of the fader in sufficient
amounts to flush debris.
4. Move the fader over its full travel back and forth a few times.
5. Shake excess fluid from the fader assembly.
6. Wipe off excess fluid.
Vue de la page 3
1 2 3 4 5 6 7 8 9 ... 18 19

Commentaires sur ces manuels

Pas de commentaire