Rane SIXTY-EIGHT Manuel de l'opérateur télécharger pdf (Page 30)

will be green. Press the x button to clear

the loop. If you click on the locked loop

symbol, a red border will appear. This

indicates the loop is locked, and you

will not be able to adjust the end points

or delete the loop until you unlock it, by

clicking on the number again.

NOTE: Looping applies to REL and INT

modes.

Auto-Looping

Auto-looping

allows you to

create loops

instantly. If

the track has

a BPM value simply click the number of

beats you wish to loop and Scratch Live

will create the loop for you. The loop is

snapped to the beats in the song detected

by Scratch Live so even if you press the

button slightly out of time Scratch Live will

still create a perfect loop for you.

Five auto-loop buttons are available on

screen at any one time. They range from

1/32 to 32 beats. The user can select

the auto-loop range with the  and 

buttons.

Pressing an auto-loop button will create

a loop start point from the nearest beat

to the playhead (within reason), and set

a loop endpoint in the future. Pressing

auto-loop 1 while auto-loop 1 is active will

deactivate the loop. Pressing a different

auto-loop button while looping is active

will extend the endpoint of the current

loop to the appropriate new auto-loop

length.

You can also save an auto-loop to the

next available slot. When using an auto-

loop, a  save button is visible where

the lock loop button normally is.

NOTE: Auto-looping requires the track

BPM to be set. See “Set Auto BPM” on

page 23.

The A-Slot

A special loop slot ‘A’ exists for auto-

looping. The act of using the auto-loop

buttons sets a loop in the ‘A’ slot,

following the rules above. Turning a

loop off using the auto-loop buttons

returns you to the loop slot that you

were previously in at the time you started

auto-looping. Turning the loop off using

the LOOP button leaves you in the ‘A’

slot. The ‘A’ slot is not saved to disk

automatically, pressing ‘save’ saves the

loop to the rst empty slot in 1-9.

Auto-looping shortcut keys are alt-1

to 5 for the Left Deck, and alt-6 to 0 for

the Right Deck. They correspond to the

looping buttons as laid out on screen. ie.

if the onscreen buttons display 1 2 4 8 16

beat loops, alt-1 triggers a 1 beat loop,

and alt-5 triggers a 16 beat loop.

Loop Roll

Loop roll performs a standard auto-

loop, but when the loop is turned off,

the playback position is returned to the

position where it would be if it had not

entered the loop (much like censor).

The other difference between loop

roll and standard auto-loop is the ‘‘roll’’

button is momentary. The loop is engaged

when the button is pressed down, and

disengaged when the button is released.

Use short loop lengths to create “stutter”

type effects.

To activate loop roll, hold control + alt

while clicking on the desired autoloop

increment, or use the keyboard shortcuts:

control + alt + 1 through 5 for the Left

Deck and control + alt + 6 through 0 for

the Right Deck. (ie. the same as the auto-

loop controls with the additional ‘alt’ key

as a modier).

The range of values available for loop

roll are 1/32 through to 32 beats. The

shortcut keys will activate whichever loop

lengths are visible on screen, i.e., if you

have lengths of a 1/4 beat through to 4

beats visible for the Left Deck, control +

alt + 1 will activate a 1/4 beat loop roll,

control + alt + 2 will activate a 1/8 beat

loop roll and so on.

Use the  and  buttons to toggle

through the range of possible lengths

visible onscreen.

Loop Roll with MIDI

You can assign loop roll to MIDI two ways:

1. After pressing the MIDI assign button

in Scratch Live, press the control + alt

keys, click on an auto-loop value, then

click on the button/slider you want it

mapped to on your MIDI controller.

2. You can assign the singular loop roll

button to MIDI, then assign a MIDI

knob or slider on your controller to the

autoloop select knob (visible in the MIDI

assign panel area when in MIDI assign

mode) to change the values on the y.

TIP: When you have the “Autoloop

Select” knob assigned to MIDI, you

have all of the loop roll lengths at your

disposal. This allows you to roll up and

down the loop length scale, to create

interesting stutter and build-up effects.

NOTE: Like auto-loop, loop roll requires

a BPM value written to the ID3 tag in

order to work. Build overviews with the

“Set Auto BPM” box checked and the

proper range for your music selected

to ensure an accurate BPM value. See

“Set Auto BPM” on page 23

RANE SIXTY-EIGHT MIXER FOR SERATO SCRATCH LIVE • OPERATOR’S MANUAL 2.4.4

1 2 ... 25 26 27 28 29 30 31 32 33 34 35 ... 59 60

Commentaires sur ces manuels

Pas de commentaire

Rane SIXTY-EIGHT Manuel de l'opérateur Page 30

Commentaires sur ces manuels

Produits connexes et manuels pour Contrôleurs de DJ Rane SIXTY-EIGHT