Rane SL 3 Manuel de l'opérateur télécharger pdf (Page 21)

RANE SL3 FOR SERATO SCRATCH LIVE • OPERATOR’S MANUAL 2.5.0

SP-6 Pitch Controls

There are

individual

Pitch Slider,

Bend, Nudge, and Keylock controls

for each sample slot. The BPM is also

displayed next to the pitch slider. If no

BPM is present in the tracks ID3 tag,

the pitch of the track is displayed as a

percentage.

Click and drag the pitch slider to make

regular pitch adjustments. Hold the shift

key and move the pitch slider to make ne

pitch adjustments.

Click on the + and – buttons to nudge

the track into time. (temporary pitch

adjustment)

Hold the ctrl key and click the + and

– buttons to make ultra-ne pitch

adjustments to nudge the track, adjusting

the pitch permanently.

SP-6 ‘Play From’ Selector

Use the

“Play From”

selector to choose where the track will

play from. You can choose to play a

track from the start of the le, any one of

the cue points, or any one of the loop in

points.

When this is set to play from start, or

play from a cue point, the track will play

right through until stopped. When a loop is

selected, the track will play until the loop

out point, unless you have “track repeat”

on, in which case the track will loop using

the in and out points of the selected loop.

The number of options will be

dependent on the number of cue points

and loops already set in your track. i.e

if the track loaded has no cue points

and loops set, then only “start” will be

available as a “Play From” option.

TIP: To set or adjust cue and loop

information for a track, load it to a

Virtual Deck, make your adjustments,

then load it back into the sample slot.

SP-6 Track Overviews

Displays an

overview of the

track loaded to each sample slot. The

waveform, play head position, cue points

and selected loops will all be visible.

SP-6 Slot Volumes

Each sample

slot has a

separate

volume slider and gain control.

Volume Sliders - Use the volume slider to

mix and make temporary adjustments to

the volume of the sample you are playing.

You can use these sliders like you use the

line faders or up faders on your DJ mixer,

fading from full volume right through to

completely silent.

Gain Knobs - In addition to the volume

slider there is an additional gain knob for

each slot. These allow you to ne tune

the maximum gain volume of the loaded

sample. The gain adjustment will also be

written to the track’s ID3 tag, meaning that

it will be the same everytime you load it.

SP-6 Output Selector

Use the master output

selector button to

choose where you wish

to send the SP-6 output.

L outputs through the left channel

M outputs through both channels (mix)

A outputs through the aux channel (1 & 2)

R outputs through the right channel

If you have the output set to Aux and click

on the SP-6 THRU button, the sample

player will automatically switch to use

the Main mix output. This prevents a

feedback loop from occurring.

There is also a master sample

player Gain knob to adjust the

overall SP-6 volume.

Individual Output Selectors

By default

each sample

slot will be set to Master, mirroring the

SP-6 master output setting. You can

however, use the individual output

selector buttons to override the master

output setting.

To send an individual slot to a different

output from the master, deselect the

master option by clicking on the master

button for the corresponding slot.

This will unlink the sample slot from the

master sample player output selection,

allowing you to choose the L, M, A,

R output for each slot. These output

routings will be saved when you close

down Scratch Live, so the next time

you launch Scratch Live, your preferred

settings will remain the same.

SP-6 Sample Banks

The SP-6 has four separate

sample banks, labeled A, B,

C and D. To switch between

the different banks click on the A, B, C

or D buttons. Each bank will save the

individual sample and sample slot settings

you last used, allowing you to prepare

banks for easy recall at a later stage.

Sample Bank A will load as the default.

SP-6 Mute Buttons

Use the mute buttons to mute the

audio output for each of the SP-6’s

sample slots. Click the mute button to

silence the audio output, click the mute

button again to turn the audio back on.

You can also ctrl-click on the mute

buttons to mute the outputs momentarily,

meaning that the audio will only be muted

for as long as you hold your mouse click.

TIP: You can MIDI assign these buttons,

allowing you to create a virtual kill

switch for the sample slot. To MIDI

assign momentary mute, hold ctrl and

click on the mute button before tapping

your MIDI controller.

SP-6 MIDI

All features of the SP-6 are MIDI

assignable. The SP-6 window must be

opened rst before enabling MIDI assign

mode. See “MIDI Control” on page

23.

1 2 ... 16 17 18 19 20 21 22 23 24 25 26 ... 43 44

Commentaires sur ces manuels

Pas de commentaire

Rane SL 3 Manuel de l'opérateur Page 21

Commentaires sur ces manuels

Produits connexes et manuels pour Contrôleurs de DJ Rane SL 3